Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - erikm

Pages: 1 ... 3 4 [5] 6 7 8
61
LPC9xx/LPC9xxx / Re: Problems with P89LPC935
« on: November 16, 2006, 05:05:33 am »
I don't understand anything. Why the device is good the first time and never more

62
P89V51Rx2/P89LV51Rx2 / Re: 89V51RD2 ISP Command Unknown
« on: November 08, 2006, 08:54:42 am »
 it was probably anticipated that the new bootloader would be in widespread use fairly quickly. From our experience that is what usually seems to happen

I would be careful with that assumption.  There have been posts from people in farawayistan that purchased 'new' chips that had been made ages ago and the problems they incurred took long to detect simply because nobody assumed they still existed in 'new' chips.

Erik


63
LPC9xx/LPC9xxx / Re: Programming P89LPC935
« on: November 08, 2006, 08:49:12 am »
the fact is that ISP IS slow, live woth it.  If you need speed and volume, use a parallel programmer.  ISP was never intended to be a speed demon.  In industrial environments ISP is not even considered.  The REAL advantage of ISP is 'field upgrades' where speed does not matter (you are only programming one)

Erik


64
is it just possible ....
that with certain security bits set FM will show the sectors erased evrn though they are not?

Erik


65
P89V51Rx2/P89LV51Rx2 / Re: Flash memory is not retaining the program
« on: October 16, 2006, 02:29:25 pm »
just a guess

what would happen if FM is still connected?

Erik


66
General / Re: Flash Magic using USB to Serial Port cable
« on: October 16, 2006, 06:17:50 am »
yes and no

This has been discussed ad nauseam and it seems that some USB to Serial Port converters will let you do it, others will not.

My GUESS is that it will be related to the handling of DTR, CTS, ... or timing, but seek and ye shall find, or mybe, I hope so for you, someone will post "the xxx USB to Serial Port converter works with FM"

erik


67
the devices are only ALMOST identical.  You WILL have to make a few code changes.

The 6/12 clock mechanism is different and do thus need to be changed.  a .hex fike that set the C type to 6 clock will set the V type to 12 clock

Erik


68
LPC9xx/LPC9xxx / Re: p89lpc922fn
« on: October 02, 2006, 07:21:07 am »
do note thet while 'the article' is about the Rx2 devices, it applies to the LPCs as well

Erik


69
LPC9xx/LPC9xxx / Re: Can programm my MCU only one Time (LPC935()
« on: September 21, 2006, 08:01:17 am »
my programmer circuit is ok and works good bevor. i use it over 2 years long now and i have net hed any problem with the programmer and reprogramming the mcu.

two possibilities

1) the most likely
The circuit is from:
http://www.esacademy.com/software/flashmagic/appnotes/ISPHardwareEntryAppNote.pdf
site 5 and it works great. ok.

you have substituted something and ended up with "a defective circuit that works"  such is VERY common and to make such show the problem can take something as simple as a change in temperature.  The callic is "My 232 inetrface is "tested and proven" now it does not work and after dragging along it is revealed that it does not work now because the PC was replaced.

2) something in your hardware is broken

Erik


70
P89V51Rx2/P89LV51Rx2 / Re: Problem with P89V51RB2FN
« on: September 19, 2006, 05:38:17 am »
Could you give any advices to solution this prob?

a guess

You have some protection bit(s) set.

for obvious reasons, if any protection is set a full erase is required.

erik


71
P89V51Rx2/P89LV51Rx2 / Re: Where can I find ISP schematics of 89LV51RD2
« on: September 14, 2006, 06:09:13 am »
I had an embedded board for P89V51RD2 (5V) and I 've modified it for P89LV51RD2 (3V)

sou8nds like you now have a 5V RS232 transciever running off 3V that will NOT work,

Erik


72
P89C51Rx+/P89C51Rx2/P89C66x/P89C6xX2/P89V66x / Re: again iap trouble
« on: September 12, 2006, 05:19:17 am »
vector corruption is not FM but the UTTERLY STUPID read of the datasheet showing a RC reset.  a RC reset with a frash based chip WILL fail.

Erik


73
LPC9xx/LPC9xxx / Re: LPC935 automatically goes to ISP
« on: August 30, 2006, 10:12:02 am »
so no_touch is triggered by a uart character (it will become 'boot' in the future but is 'x' at this moment)


That is your problem, the UART often read a garbage character during power up.  Change the request to 4 or more sequential characters and it will work.

Erik


74
LPC9xx/LPC9xxx / Re: LPC935 automatically goes to ISP
« on: August 30, 2006, 06:06:57 am »
it must be yout 'NoTouch trigger' that get activated accidentially.

post the code for the trigger

Erik


75
LPC9xx/LPC9xxx / Re: P89LPC9221 FAQ
« on: August 09, 2006, 07:25:53 am »
and I have built a circuit same with MCB900

99.17% of the time the answer is

EXACTLY SAME?? no component substitutions, no "i have this transistor, I'll just use it" etc

Erik


Pages: 1 ... 3 4 [5] 6 7 8