Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - Andy Ayre

Pages: 1 [2] 3 4 ... 146
General Discussion / Re: Stall + Not authorized
« on: April 16, 2018, 03:27:54 am »
Can you please try this:

Install version 11.00.
Open a command window and go to the FM installation folder
Connect the LPC-Link2 with JP1 removed

  USBManger --list

What happens? What is output? Do you hear any bings/bongs from Windows? Does the LED on the Link2 start flashing?

Thanks, Andy

General Discussion / Re: Stall + Not authorized
« on: April 16, 2018, 01:19:06 am »
Close FM
Remove jumper JP1 from the LPC-Link2
Connect the LPC-Link2 to your PC - make sure it is recognized by checking in device manager
Start FM

Currently FM only checks for attached debug hardware on startup.

Do you have three different PCs giving the "not authorized" error?

General Discussion / Re: Slow download which bugs out Chrome
« on: April 12, 2018, 03:21:38 am »
Thanks for the additional information. Looking at the web server logs and your IP address there is an error message that indicates the connection is being prematurely closed at the client before the server had chance to respond. In this case the result is error code 500 - Internal Server Error, which is misleading. My guess is that a slow connection somewhere along the way was causing your browsers to give up just at the point where the web server was about to send a response.

General Discussion / Re: Slow download which bugs out Chrome
« on: April 11, 2018, 02:05:31 am »
I just tried Microsoft Edge 41.16299.248.0 on Windows 10 Pro 64-bit version 1709. It downloaded in 10 seconds and opens fine. I then tried it a three more times, clearing the browser cache each time. Always downloaded successfully and takes about 10 seconds.

I then tried Chrome 65.0.3325.181 on the same PC.  Took about 10 seconds, downloaded successfully. I tried it a few more times - always around 10 seconds and always successful.

I then tried Firefox 59.0.2 64-bit on the same PC. Downloads in about 10 seconds, downloads successfully.

We have also tried downloading from UK, USA and Germany - seems to download fine.

I would suspect your internet connection or somewhere between your PC and our server, on the internet perhaps.

ARM Cortex / Re: LPC1112 Bootloader - shared serial port
« on: April 11, 2018, 01:46:51 am »
I wouldn't recommend it.


General Discussion / Re: Stall + Not authorized
« on: April 09, 2018, 03:22:36 am »
I guess an errant Windows update broke something, but perhaps they have now fixed it. Thanks for posting an update.

General / Re: Can I flash two hex files to LPC11u3x using flash magic
« on: April 09, 2018, 03:21:53 am »
Yes, you can. Simply avoid erasing after programming the first hex file.

ARM Cortex / Re: LPC1112 Bootloader - shared serial port
« on: April 09, 2018, 03:21:14 am »
UART/RS232 is point-to-point and isn't designed for multiple devices to be attached to it. Use jumpers or tri-state outputs instead.

General Discussion / Re: Slow download which bugs out Chrome
« on: April 05, 2018, 09:17:24 pm »
Hmmm... downloads seem slow for me as well, but using Chrome the downloads are successful. We will keep monitoring it to see if there is a pattern.

General Discussion / Re: Stall + Not authorized
« on: April 02, 2018, 08:27:28 pm »
Can you please give me a list of all updates you have on your PC - should be able to see them in Control Panel -> Uninstall Applications. What was installed between the last time it ran OK and March 26th?

Also what service pack level are you at with Windows 7?

Meanwhile version 10.90 is available that does not have this problem.

Thanks, Andy

Please send a debug file showing programming and verify to support at esacademy dot com.

General Discussion / Re: Access Violation in Windows 10
« on: March 23, 2018, 07:08:15 am »
Yes, this is a known problem with the "display memory" feature. We are looking at it.

General Discussion / Re: Crashing on Windows 10
« on: March 23, 2018, 07:07:26 am »
First please uninstall your current version, download the latest version, install it and see if it works. We have it running on Windows 10 without a problem.

Feature Requests / Re: custom message
« on: March 12, 2018, 01:57:04 am »
Good idea. We will consider it for a future release.

ARM Cortex / Re: LPC11C24F programming
« on: February 05, 2018, 01:01:35 am »
You have probably damaged it by applying 30V. It's far too much.


Pages: 1 [2] 3 4 ... 146