- Welcome to Flash Magic Forum.
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages1
#2
LPC9xx/LPC9xxx / Re: Additional secuirity bits can not be cleared
August 28, 2006, 06:21:48 PM
Hi Andy,
Thanks for your response.Using your solution
Go to ISP -> Device Configuration Click on "Clear Config Protection",I can clear all of the Additional secuirity bits--AWP,CWP and DCCP successfully.
Thanks!
Thanks for your response.Using your solution
Go to ISP -> Device Configuration Click on "Clear Config Protection",I can clear all of the Additional secuirity bits--AWP,CWP and DCCP successfully.
Thanks!
#3
LPC9xx/LPC9xxx / Additional secuirity bits can not be cleared
August 25, 2006, 07:10:10 PM
Hi Andy,
I tested the writing and reading"Additional secuirity bits"on an LPC935 device by MCB900,which configed with an ICP kit(work with FLASHMAGIS).I find the CWP bit can be set to 1,but can not be clear to 0!Why can do this?
Thanks!
I tested the writing and reading"Additional secuirity bits"on an LPC935 device by MCB900,which configed with an ICP kit(work with FLASHMAGIS).I find the CWP bit can be set to 1,but can not be clear to 0!Why can do this?
Thanks!
#4
LPC9xx/LPC9xxx / Re: P89LPC9221 FAQ
August 13, 2006, 08:37:20 PM
Hi Ivan,
If you have installed the KEIL uVision3,you can find the schematics of
the latest version MCB900 in this help file:
X:\Keil\C51\hlp\mcb900.chm (where :"X" stands for hard disk for the setup).
You can download a demo version uVision3 from KEIL.The Keil C51 Evaluation Kit allows you to create programs for all 8051 derivatives.
The SETUP program is on the following link:
http://www.keil.com/kdl/p3hq3symwqrpthwwzj3v31dctd/files/eval/c51v805.exe
If you have installed the KEIL uVision3,you can find the schematics of
the latest version MCB900 in this help file:
X:\Keil\C51\hlp\mcb900.chm (where :"X" stands for hard disk for the setup).
You can download a demo version uVision3 from KEIL.The Keil C51 Evaluation Kit allows you to create programs for all 8051 derivatives.
The SETUP program is on the following link:
http://www.keil.com/kdl/p3hq3symwqrpthwwzj3v31dctd/files/eval/c51v805.exe
#5
LPC9xx/LPC9xxx / Re: P89LPC9221 FAQ
August 07, 2006, 10:00:34 PM
Flash Download to MCB900
You can download the HEX file into on-chip Flash ROM of the P89LPC922 device on the MCB900 Evaluation Board. You need to setup the MCB900 board as described below:
Configure the Jumper Settings for FlashMagic: RUN - OFF, RESET - ON
Connect the COM Port to the PC COM1 interface using a standard 9-pin connector cable.
Connect the MCB900 Board to a power supply (5V .. 9V=, 100mA)
You have two alternatives for Flash programming: use the
You can download the HEX file into on-chip Flash ROM of the P89LPC922 device on the MCB900 Evaluation Board. You need to setup the MCB900 board as described below:
Configure the Jumper Settings for FlashMagic: RUN - OFF, RESET - ON
Connect the COM Port to the PC COM1 interface using a standard 9-pin connector cable.
Connect the MCB900 Board to a power supply (5V .. 9V=, 100mA)
You have two alternatives for Flash programming: use the
#6
LPC9xx/LPC9xxx / Re: CRC incorrect on Flash Magic version 3.13
July 19, 2006, 06:24:16 PM
Thanks for your attention!I am looking forward to getting a perfect version.
#7
LPC9xx/LPC9xxx / Re: CRC incorrect on Flash Magic version 3.13
July 18, 2006, 07:11:38 PM
Hi Andy,
An email has been sent to you already.Thanks for investigating
the problem.
An email has been sent to you already.Thanks for investigating
the problem.
#8
LPC9xx/LPC9xxx / Re: CRC incorrect on Flash Magic version 3.13
July 18, 2006, 12:03:08 AM
why did not fix the "hex files CRC" incorrect bug in Version 3.20?
#9
LPC9xx/LPC9xxx / Re: CRC incorrect on Flash Magic version 3.13
July 17, 2006, 08:10:57 PM
sorry!:)
but can you solve this problem?Thanks!
but can you solve this problem?Thanks!
#10
LPC9xx/LPC9xxx / Re: CRC incorrect on Flash Magic version 3.13
July 17, 2006, 07:24:00 PM
how can I upload attachment when post my topic?
#11
LPC9xx/LPC9xxx / CRC incorrect on Flash Magic version 3.13
July 17, 2006, 07:20:35 PM
Hi esacademy,
I made an ICP programmer,which repotted from the MCB900 and the ISP-TO-ICP bridge code v1.6. When I programing the LPC900 devices with the FM version 2.52 by this ICP kit,everything is OK! but after updating the FM to version 3.13,the CRC is not correct.how can make this?Thanks in advance for your reply !
Best Regards
I made an ICP programmer,which repotted from the MCB900 and the ISP-TO-ICP bridge code v1.6. When I programing the LPC900 devices with the FM version 2.52 by this ICP kit,everything is OK! but after updating the FM to version 3.13,the CRC is not correct.how can make this?Thanks in advance for your reply !
Best Regards
Pages1