Author Topic: XA-G49 reg.  (Read 23804 times)

nitin52

  • Jr. Member
  • **
  • Posts: 5
    • View Profile
XA-G49 reg.
« on: December 15, 2005, 01:04:40 AM »
Hello,
Please refer to Lash Magic User Manual page 41 and the following lines.

"The following simplified circuit diagram for an 89C51RD2 is one possible way of connecting the DTR and RTS signals to RST and /PSEN of the device. Note that minor changes would have to be made to use this circuit with the XA devices."

It says minor changes are required for XA devices. I would like to know what are they. Thanks.
Nitin

Andy Ayre

  • ESAcademy Staff
  • Sr. Member
  • *****
  • Posts: 2190
    • View Profile
    • Embedded Systems Academy, Inc.
    • Email
Re: XA-G49 reg.
« Reply #1 on: December 15, 2005, 06:19:10 AM »
The diagram was designed for 8051s with an active high reset. The XA-G49 has an active low reset. Please refer to the ISP section of the XA-G49 datasheet for the ISP entry requirements.

Embedded Systems Academy, Inc.
support at esacademy dot com

Rons

  • Jr. Member
  • **
  • Posts: 55
    • View Profile
Re: XA-G49 reg.
« Reply #2 on: December 15, 2005, 08:38:59 AM »
It's a little more involved than that. The EAN/WAIT pin is sampled on reset
and this will determine the memory configuration. Philips has a application
Note the talks about it. I use a 74LS74 in my designs.

nitin52

  • Jr. Member
  • **
  • Posts: 5
    • View Profile
Re: XA-G49 reg.
« Reply #3 on: December 15, 2005, 06:16:55 PM »
Thanks for the info.

Rons

  • Jr. Member
  • **
  • Posts: 55
    • View Profile
Re: XA-G49 reg.
« Reply #4 on: December 16, 2005, 10:45:56 AM »
Get App note AN96075. It will tell you everything.

erikm

  • Full Member
  • ***
  • Posts: 113
    • View Profile
Re: XA-G49 reg.
« Reply #5 on: December 16, 2005, 12:58:51 PM »
x

erik

nitin52

  • Jr. Member
  • **
  • Posts: 5
    • View Profile
Re: XA-G49 reg.
« Reply #6 on: December 16, 2005, 06:54:54 PM »
Hello Rons,
AN96075 is about using EAn/WAIT pin and not what I am looking for.
Nitin

Rons

  • Jr. Member
  • **
  • Posts: 55
    • View Profile
Re: XA-G49 reg.
« Reply #7 on: December 17, 2005, 03:09:33 PM »
Well, you had better understand AN96075. It deals with the "RST" pin.
As to your "minor changes". Reversing the reset capacitor and charging
resistor connections are all thats probably needed.

nitin52

  • Jr. Member
  • **
  • Posts: 5
    • View Profile
Re: XA-G49 reg.
« Reply #8 on: December 18, 2005, 06:36:58 PM »
Hello Rons,
Along with reversing the reset capacitor and charging resistor connections, we have to connect the input of 74LS125 tri state buffer to ground (VSS) insted of VCC.
Nitin

erikm

  • Full Member
  • ***
  • Posts: 113
    • View Profile
Re: XA-G49 reg.
« Reply #9 on: December 27, 2005, 09:37:45 AM »
Reversing the reset capacitor and charging
resistor connections are all thats probably needed.

maybe, but I have yet to find ANY flash micro that does not occasionally "lose its memory" when reset by RC.

USE A SUPERVISOR CHIIP

Erik

erik

Rons

  • Jr. Member
  • **
  • Posts: 55
    • View Profile
Re: XA-G49 reg.
« Reply #10 on: January 05, 2006, 12:04:20 PM »
!x

nitin52

  • Jr. Member
  • **
  • Posts: 5
    • View Profile
Re: XA-G49 reg.
« Reply #11 on: January 05, 2006, 06:15:50 PM »
Whats that Rons  !x